| MALFUNCTION
CODE |
DETECTED
ITEM |
DETECTED
FAILURE CONDITION
-------------------------------------
CHECK FOR |
| c00 |
No
Fault |
------------- |
| c11 |
Cam
position sensor |
The
signal does not reach ECM for more than 2 sec. after receiving
the starter signal
--------------------------------------------------------------------------------------
The camshaft position sensor wiring and mechanical
parts. (Camshaft position sensor, rear intake cam pin,
wiring/coupler connection) |
| c12 |
Crankshaft
position sensor |
The
signal does not reach ECM for more than 2 sec. after receiving
the starter signal
--------------------------------------------------------------------------------------
The crankshaft position sensor wiring and mechanical
parts. (Crankshaft position sensor, wiring/coupler
connection) |
| c13 |
Intake
air pressure sensor |
The
sensor should produce the following voltage. (0.5 V
< or = sensor voltage < 4.5 V) Without this
range c13 is indicated.
--------------------------------------------------------------------------------------
Intake air pressure sensor,
wiring/coupler connection |
| c14 |
Throttle
position sensor |
The
sensor should produce the following voltage. (0.2 V
< or = sensor voltage < 4.8 V) Without this
range c14 is indicated.
--------------------------------------------------------------------------------------
Throttle position sensor,
wiring/coupler connection |
| c15 |
Engine
coolant temperature sensor |
The
sensor voltage should be the following. (0.15 V <
or = sensor voltage < 4.85 V) Without this range
c15 is indicated.
--------------------------------------------------------------------------------------
Engine
coolant temperature sensor,
wiring/coupler connection |
| c21 |
Intake
air temperature sensor |
The
sensor voltage should be the following. (0.15 V <
or = sensor voltage < 4.85 V) Without this range
c21 is indicated.
--------------------------------------------------------------------------------------
Intake
air temperature sensor,
wiring/coupler connection |
| c22 |
Atmospheric
pressure sensor |
The
sensor voltage should be the following. (0.5 V < or
= sensor voltage < 4.85 V) Without this range c22
is indicated.
--------------------------------------------------------------------------------------
Atmospheric
pressure sensor,
wiring/coupler connection |
| c23 |
Tip
over sensor |
The
sensor voltage should be less than the following for
more than 8 sec. after ignition switch turns ON. (0.25
V < or = sensor voltage < 4.85 V) Without this
value c23 is indicated.
--------------------------------------------------------------------------------------
Tip
over sensor,
wiring/coupler connection |
| c24 |
Ignition
signal #1 (Front Cylinder) |
Crankshaft
position sensor (pick-up coil) signal is produced but
signal from ignition coil is not produced continuous
two times. In this case, the code c24 is indicated.
--------------------------------------------------------------------------------------
Ignition coil, wiring/coupler connection, power supply
from the battery |
| c25 |
Ignition
signal #2 (Rear Cylinder) |
Crankshaft
position sensor (pick-up coil) signal is produced but
signal from ignition coil is not produced continuous
two times. In this case, the code c25 is indicated.
--------------------------------------------------------------------------------------
Ignition coil,
wiring/coupler connection, power supply from the
battery |
| c31 |
Gear
position signal |
Gear
position signal voltage should be higher than the
following for more than 2 seconds. (Gear position
sensor voltage > 0.60 V) Without this value c31 is
indicated.
--------------------------------------------------------------------------------------
Gear
position signal,
wiring/coupler connection, Gearshift cam etc. |
| c32
or c34 |
Fuel
injector signal #1 or #2 (Front Cylinder) |
Fuel
injection signal stops, the c32, c33, c34 or c35 is
indicated.
--------------------------------------------------------------------------------------
Injector, wiring/coupler connection, power supply to
the injector. |
| c33
or c35 |
Fuel
injector signal #3 or #4 (Rear Cylinder) |
Fuel
injection signal stops, the c32, c33, c34 or c35 is
indicated.
--------------------------------------------------------------------------------------
Injector,
wiring/coupler connection, power supply to the
injector. |
| c41 |
Fuel
pump relay signal |
When
no signal from fuel pump relay, c41 is indicated
--------------------------------------------------------------------------------------
Fuel pump relay, connecting lead, power source to fuel
pump relay. |
| c42 |
Ignition
switch signal |
Ignition
switch signal is not input in the ECM.
--------------------------------------------------------------------------------------
Ignition switch, lead wire/coupler. |
